Omnio DIN rail mounted thermostat actuator 8-channels REGH12/08

The Omnio DIN rail mounted multi thermostat actuator 8-channels REGH12/08 is a device to regulate control valves in floor heatings or similar electric loads through a two-point controller with hysteresis. Each of its eight potential free outputs is able to be controlled by an Omnio room sensor RTF and up to eight Omnio window contacts

Omnio flush mounted repeater UPR230/03

The Omnio flush mounted repeater UPR230/03 is a device to enhance the radio telegrams between Omnio radio transmitters and sensors. This repeater is useful if the next actuator is it out of reach. All received and valid telegrams will be enhanced and sent onward. Suitable for flush- or surface mounted sockets. Information: The repeater function

Omnio flush mounted push-button interface 2-channels TST230/12

The Omnio flush mounted push-button interface 2-channels TST230/12 is a binary input device to integrate wired push-buttons, switches and sensors into the Omnio radio system. One potential free and one non-isolated 230 V~ closing contact may be connected to its inputs. Depending on the chosen evaluation (rocker-switch, push-button, time switch or weather station) the push-button

Omnio flush mounted push-button interface 2-channels TST230/10

The Omnio flush mounted push-button interface 2-channels TST230/10 is a binary input device to integrate wired push-buttons, switches and sensors into the Omnio radio system. Two potential free closing contacts may be connected to its inputs. Depending on the chosen evaluation (rocker-switch, push-button, time switch or weather station) the push-button interface transmits, repeats and additionally

Omnio Gateway APG03B-RS485

The Omnio gateway APG03B-RS485 serves as bidirectional gateway between Omnio and computer systems with RS485 interface. It receives and transmits all valid EnOcean radio telegrams. The used protocol is completely open, which easily allows the integration in personal systems. Configuration is carried out via ARCO technology (AWAG Remote Commissioning) with the E-Tool Freeware. Suitable for

USB-Gateway SG-USB300

The gateway SG-USB300 serves as bidirectional gateway between Omnio and computer systems with a USB interface. This gateway is equipped with the EnOcean radio module TCM 300.

Omnio Gateway 32-channels APG01-KNX

The Omnio radio gateway APG01-KNX2 serves as bidirectional gateway between Omnio and the KNX bus. With this device, commands and measured values from EnOcean wireless sensors can be transmitted to the KNX bus, for example to control KNX actuators. EnOcean wireless actuators can also be controlled via KNX. The gateway supports the encrypted wireless communication

Omnio flush mounted universal dimmer 1-channel UPD230/10

The Omnio flush mounted universal dimmer 1-channel UPD230/10 with extension input is a device for dimming LED luminaires and other electrical loads. Thanks to automatic load recognition (R/L/C) the dimmer selects the right operating mode as well as the ideal dimming curve for the connected light source. Up to 50 Omnio radio transmitters can be

Omnio universal cable dimmer 1-channel KD230/10

The Omnio universal cable dimmer 1-channel KD230/10 is a device for dimming LED luminaires and other electrical loads. Thanks to automatic load recognition (R/L/C) the dimmer selects the right operating mode as well as the ideal dimming curve for the connected light source. Up to 50 Omnio radio transmitters can be programmed. Each transmitter can

Omnio flush-mounted blind actuator 1-channel UPJ230/12

The Omnio flush-mounted blind actuator 1-channel UPJ230/12 is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its two potential free interlocked outputs are able to regulate one drive and can be actuated from up to 50 Omnio radio transmitters. This allows the exact positioning of