e.g. EU, Non-EU Europe, China, Singapure, …

AL-443-00-868 EnoSense® LUX / CE – Precise ambient light sensor

Our new sensor works with an internal battery for use in any ambient light situation. The EnoSense® LUX transmits its current measured value every 15 minutes, and even every minute if there is a change. With its stylish design housing, it fits unobtrusively on any wall and is only 81 x 41 x 9 mm

AL-435-00-868 EnoSense® Temp/RH / CE – Precise EnOcean Sensor for temperature and humidity

Our new EnOcean temperature sensor works with an internal battery for use in any ambient light situation. In addition to temperature, it also measures relative humidity. The EnoSense® Temp/RH sends its current measured values every 15 minutes, and even every minute if there is a change. With its stylish design housing, it fits unobtrusively on

AL-437-03-868 EnoSense® DESK / CE – Optimized EnOcean Sensor for desksharing

Compared to the EnoSense® WALL & DESK, our new sensor has a motion detector (PIR) in addition to a vibration sensor. This enables it to detect movements below the edge of the desk and recognise people even if they do not touch the desk for a longer period of time due to their activity. It

AL-431-00-868 EnoSense® WALL+DESK / CE – EnOcean Sensor for desksharing

This small EnOcean sensor is powered by its integrated solar cell and supplies its measured values at configurable intervals. The sensor, which is snapped into a housing, is attached with a double-sided adhesive pad, preferably on the table top at a corner of the workstation. Depending on the colour of the desk, the sensor is

VL-700 BASE / CE – EnOcean Gateway and Edge Controller

The VL-700 BASE serves as an IoT edge controller which, with the pre-installed software, is able to receive and interpret data from up to 32 EnoDisc® and send it to a cloud, for example. Optionally, the data can also be evaluated locally and/or transferred to the building automation system. The usual interfaces such as BACnet,

AL-602-02-868 EnoPuck® CO2 WALL / CE – EnOcean CO2 sensor and LED display

EnoPuck CO2 WALL: The CO2 traffic light “EnoPuck CO2” has been supplemented with a mounting ring for the wall and the appropriate holders on the device especially for front wall mounting. In addition, the power supply is provided via a twin stranded wire, which is routed out of the back of the device, instead of

AL-602-01-868 EnoPuck® CO2 / CE – EnOcean CO2 sensor and LED display

The “EnoPuck CO2” CO2 traffic light can be used both as a stand-alone solution and in conjunction with a building automation system. Unlike many other solutions, the bright RGB LEDs make the light signal clearly visible at all times, even from a greater distance. The CO2 measured value is measured and displayed in the individual

AL-440-00-868 EnoSense® NOISE / CE – EnOcean Sound level meter

Our new sensor for measuring the sound pressure level on site normally works energy self-sufficiently via the integrated solar cell when there is sufficient light. The EnoSense® NOISE transmits its current measured values every 4 minutes. To provide the best possible support for maintenance and diagnostics, it also delivers all relevant energy values to the

AL-439-00-868 EnoSense® CO2 / CE – EnOcean CO2 sensor plus temperature and humidity

Our new CO2 sensor operates energy self-sufficiently via the integrated solar cell when there is sufficient illuminance. The EnoSense® CO2 sends its current measured values every 5 minutes. In addition to CO2, the sensor measures the relative humidity. humidity and the air temperature. To provide the best possible support for maintenance and diagnostics, it also

AL-436-00-868 EnoSense® People Counter / CE – EnOcean People counting

This easy-to-install sensor for counting people passing by is powered by two AA batteries and transmits its data wirelessly with every counting event. The sensor is attached to the door frame above the door, preferably on the hallway side, using a double-sided adhesive pad (included). Depending on the color of the door frame, the sensor