Omnio DIN rail mounted switching actuator 4-channels REGS12/04

The Omnio DIN rail mounted switching actuator 4-channels REGS12/04M is a device for switching electrical loads. Its four potential free outputs are able to be actuated from up to 50 Omnio radio transmitters. Each transmitter can be programmed with one out of twenty different functions such as switch, push-button, staircase lighting, step-switch (AW20), time controlled

Omnio flush-mounted multi switching actuator 1-channel UPS230/10

The Omnio flush-mounted multi switching actuator 1-channel UPS230/10 is a device for switching electrical loads. Its potential free output is able to be actuated from up to 50 Omnio radio transmitters. Each transmitter can be programmed with one out of twenty different functions such as switch, push-button, staircase lighting, step-switch (AW20), time controlled switch (AW23/24/25),

Omnio flush-mounted switching actuator 1-channel UPS230/08

The Omnio flush-mounted switching actuator 1-channel UPS230/08 is a device for switching electrical loads. Its potential free output is able to be actuated from up to 50 Omnio radio transmitters. Each transmitter can be programmed with one out of twenty different functions such as switch, push-button, staircase lighting, step-switch (AW20), time controlled switch (AW23/24/25), window

Omnio Room Sensor RTF161

The Omnio room sensor RTF- 161 is a battery less, maintenance-free and wireless sensor to measure temperature (0…40 °C) and humidity (0…100 %rH) indoors. The temperature can be set with its operation elements (set point). It is able to transmit temperature, humidity and set point via radio to Omnio thermostat actuators and gateways. The RTF-

Omnio Room Sensor RTF160

The Omnio room sensor RTF- 160 is a battery less, maintenance-free and wireless sensor to measure temperature (0…40 °C) and humidity (0…100 %rH) indoors. The measured value is transmitted wireless to Omnio thermostat actuators and gateways. The RTF160 is characterised by its excellent long-term stability and thanks to the built in solar cell it is

Omnio flush-mounted multi switching actuator 2-channels UPS230/12

The Omnio flush-mounted multi switching actuator 2-channels UPS230/12 is a device for switching electrical loads. Its two potential free outputs are able to be actuated from up to 50 Omnio radio transmitters. Each transmitter can be programmed with one out of twenty different functions such as switch, push-button, staircase lighting, step-switch (AW20), time controlled switch

Omnio weather evaluation unit XFJ

The Omnio weather evaluation unit XFJ is able to convert the captured weather data into EnOcean telegrams. This way blinds can be pilot-controlled and protected against thunderstorms. The following individual signals are available: Channel 1: Weather raw data for higher-level systems according to EEP A5-13-01… 06. Channel 2: Alarm due to failure of the weather

Oil-Water Warning Indicator ÖWU

Application For visual and audible alarms if liquids with a flash point of > 55 °C are detected. Suitable for the following media: water, fuel oil, diesel fuel or low-viscosity lubricating oils, motor oils, gearbox oils or hydraulic oils, vegetable oils and transformer oils. Description Alarm unit in wall mounting housing for early detection of

Vacuum leak detector Eurovac

Application Class I vacuum type leak detector according to EN 13160 for safe monitoring of double-walled tanks and single-walled tanks with inner lining for the storage of water-polluting liquids with a flash point > 55 °C as well as AdBlue® (urea solution 32.5 %) according to DIN 70070. The broad voltage range (AC 100–240 V)

CO2 Sensor F

Application For continuous monitoring of the carbon dioxide (CO2) concentration in the ambient air. Application in rooms in which many persons work, study or live and where carbon dioxide levels may consequently be elevated. High concentrations of carbon dioxide in the ambient air reduce the ability of persons to concentrate and perform. Ideal for educational