Omnio flush mounted push-button interface 2-channels TST230/10

The Omnio flush mounted push-button interface 2-channels TST230/10 is a binary input device to integrate wired push-buttons, switches and sensors into the Omnio radio system. Two potential free closing contacts may be connected to its inputs. Depending on the chosen evaluation (rocker-switch, push-button, time switch or weather station) the push-button interface transmits, repeats and additionally

Omnio flush mounted push-button interface 2-channels TST230/12

The Omnio flush mounted push-button interface 2-channels TST230/12 is a binary input device to integrate wired push-buttons, switches and sensors into the Omnio radio system. One potential free and one non-isolated 230 V~ closing contact may be connected to its inputs. Depending on the chosen evaluation (rocker-switch, push-button, time switch or weather station) the push-button

Omnio flush mounted repeater UPR230/03

The Omnio flush mounted repeater UPR230/03 is a device to enhance the radio telegrams between Omnio radio transmitters and sensors. This repeater is useful if the next actuator is it out of reach. All received and valid telegrams will be enhanced and sent onward. Suitable for flush- or surface mounted sockets. Information: The repeater function

Omnio DIN rail mounted thermostat actuator 8-channels REGH12/08

The Omnio DIN rail mounted multi thermostat actuator 8-channels REGH12/08 is a device to regulate control valves in floor heatings or similar electric loads through a two-point controller with hysteresis. Each of its eight potential free outputs is able to be controlled by an Omnio room sensor RTF and up to eight Omnio window contacts

Omnio flush-mounted thermostat actuator 2-channels UPH230/12

The Omnio flush mounted thermostat actuator UPH230/12 is a device to regulate control valves in floor heatings or similar electric loads through a two-point controller with hysteresis. Each of its two potential free outputs are able to be controlled by an Omnio room sensor RTF and up to eight Omnio window contacts or –handles in

Omnio flush-mounted thermostat actuator 1-channel UPH230/10

The Omnio flush mounted thermostat actuator UPH230/10 is a device to regulate control valves in floor heatings or similar electric loads through a two-point controller with hysteresis. Its potential free output is able to be controlled by an Omnio room sensor RTF and up to eight Omnio window contacts or –handles in AND-operation. The room

CO2-Sensor

The CO2-sensor is a wired radio sensor to capture the concentration of carbon dioxide (400…2550 ppm) in the air. The measured values are transmitted wireless to Omnio gateways. It is particularly used to control the air quality indoors in offices, schools, hotels and residential premises. EnOcean Equipment Profile (EEP) A5-09-04.

Omnio blind cable actuator 1-channel KXJ230/12

The blind cable actuator 1-channel KXJ230/12 is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its two interlocked outputs are able to regulate one drive and can be actuated from up to 50 Omnio radio transmitters. This allows the exact positioning of the blinds and

Omnio DIN rail mounted blind actuator 4-channels REGJ12/04

The Omnio DIN rail mounted blind actuator 4-channels REGJ12/04M is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its eight potential free interlocked outputs are able to regulate four drives and these can be actuated from up to 50 Omnio radio transmitters. This allows the

Omnio flush-mounted blind actuator 1-channel UPJ230/12

The Omnio flush-mounted blind actuator 1-channel UPJ230/12 is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its two potential free interlocked outputs are able to regulate one drive and can be actuated from up to 50 Omnio radio transmitters. This allows the exact positioning of